Hauppauge Hvr 1950 Driver

Hauppauge WinTV HVR-1950 Model 75xxx, Hybrid ATSC/QAM - Driver Download. Updating your drivers with Driver Alert can help your computer in a number of ways.

Download the latest Hauppauge WinTV-HVR Series external USB TV tuner WinTV-HVR-1950 device drivers Official and Certified. Hauppauge WinTV-HVR Series external USB.

Latest applications and driver updates

WinTV version 7 application and driver

Note: If you have run HCWCLEAR, you must reboot your PC and leave the WinTV-HVR-1950 installed. After a reboot you will see the Found New Hardware Wizard installation message, hit Cancel. then continue below.

Note: to use the WinTV-HVR-1950 with Microsoft s Windows Media Center application in Windows Vista or Windows 7, you only need the WinTV-HVR driver.

WinTV v7 application and TV tuner driver download package

Note: A valid WinTV application CD-ROM will be needed to install this WinTV v7 version

Any WinTV 7 application CD can be used during the install. If you do not have your original WinTV CD-ROM but would like to update to WinTV v7 or WinTV v8, you can purchase a new CD on the Hauppauge webstore for 9.95

To install the WinTV v7 application update

Download the WinTV v7 installation package to your PC. After downloading this file, the file is normally saved in the Download directory on your PC

Insert your original valid WinTV CD in your CD-ROM drive

Run wintv7_cd from the Download directory on your PC

WinTV v7 installation package, version 3.9g

For Windows 10, 8, 7, Vista and XP

This download is a complete installation package, including drivers for supported WinTV products plus the WinTV v7 application and utilities.

A valid WinTV application CD-ROM will be needed to install this WinTV v7 version. Any WinTV v6 or WinTV 7 application CD can be used during the install. If you do not have your original WinTV CD-ROM but would like to update to WinTV v7, you can purchase a new CD on the Hauppauge webstore for 9.95

If you have a WinTV v7.2 CD-ROM with Extend, then the latest version of WinTV Extend will also be installed.

To install WinTV v7 on a PC or laptop without a CD-ROM drive

If your PC or laptop does not have a CD-ROM drive, do the following:

at the conclusion of the installation a dialog box will pop up saying Activation required

You will find the Product code on your WinTV v7 Installation CD

Enter the Product code including dashes and dots

Release notes for WinTV v7 version 3.9G:

Update to the WinTV-HVR-955Q driver to fix problems seen when switching channels quickly

Fixed an error You do not have access to make the required system configuration modifications

Increased Pause Buffer bar size

Fixed TitanTV tvpi file association bug

New WinTV-NOVA-HD-USB 2 driver to fix issues in Turkey and other countries with low symbol rates

New WinTV-HVR-1975 driver to fix issues with 6875 Symbol rate

Fixed no Extend tab showing on upgrade installation

Note to Windows Media Center users:

If you want to use WinTV-HVR-195x to watch and record analog cable TV with Microsoft s Media Center application, do the following:

When you run Media Center, go to Tasks / Settings / TV / Set Up TV signal

At Set Up your TV signal, click Next

At Regional settings, make sure your region is correct and click Next

At Download TV options, click Next.

At TV Signal, click I will configure my TV signal manually and click Next

You will then see: Cable / Satellite / Antenna. Chose the source of your TV signal Cable for use with analog cable TV and click Next.

Click through the rest of the settings, set up your Guide listings and click Finish. Then return to the main menu.

Go to TV Movies and then live TV to watch and record TV.

WinTV-HVR-19xx driver version 3.2.32350

To install the latest Windows driver only:

Leave your WinTV-HVR plugged into your PC. Follow the following steps:

Download the Windows driver above.

Double click the downloaded driver. This will install the WinTV-HVR-22xx Windows driver.

At the completion of the driver install, you should see a message which says Drivers have been updated successfully.

At this point, the Windows driver will be installed.

Setting up your TV tuner in Windows 7 Media Center

Here is a screen by screen view of the setup of Windows Media Center. It was based on the WinTV-HVR-1600, but the setup with other WinTV-HVR products will be similar.

Windows Media Center remote control receiver/blaster configuration utility

Hcwcirconfig_tool_1.2.28165.exe

Use this utility to enable or disable the built-in IR receiver/blaster hardware on the WinTV-HVR-1850 and WinTV-HVR-2250 for use with Windows Media Center. You would disable the built-in IR receiver/blaster if you are using an external USB attached Windows Media Center remote control.

Download and install the Hcwcirconfig tool

After installing the Hcwcirconfig tool, run the program. The tool will be located in Start / All Programs / Hauppauge WinTV / HCWCIRConfig Tool

To configure as a Windows Media Center remote control, put a check in the box labeled Hauppauge Consumer Infrared Receiver click OK – Save Changes.

Your computer must be restarted for the changes to take effect.

Name: Hcwcirconfig_tool_1.2.28165.exe

Bug fixes for the Windows Media Center Low bit rate error message

Microsoft has released Windows Media Center patches for the Low bit rate error message.

Click to view the information from Microsoft.

Remapping clear QAM channels in Windows 7 Media Center

Here are some instructions on remapping clear QAM TV channels in Windows Media Center.

Accessory software for the WinTV-HVR-1950

WinTV Digital Signal Strength Indicator

Signal Strength Indicator version 33310

The WinTV Digital Signal Strength indicator displays information about the quality of the digital TV channel you are watching. This application is used with the WinTV v7 and WinTV v8 applications.

Click here for instructions on using this application.

IR Remote control version 30339

Remote control applet. After you run this applet, an icon will appear in your Windows device tray showing that the Hauppauge remote control is active..

IR Blaster Configuration program

This program configures the IR blaster for use with the WinTV v7 application. Included is the selection of the set top box and the learn mode.

IR Remote/Blaster Hardware Installation Guide

IR Remote Blaster QuickInstall Guide

WinTV-Scheduler update for WinTV version 6

TV Scheduler version 25_26071.exe

This TV program scheduler for WinTV version 6 allows background recording on dual tuner WinTV products.

WinTV Radio application for use with WinTV version 6

WinTV Radio32 application version 1.54

this application runs with WinTV version 6 on WinTV boards equipped with FM radio

WinTV v7 has a built-in FM radio application

To install, download to a temporary directory and run RADIO32.EXE

New features include 30 presets and local/distance reception. Also, name radio stations by creating a preset and then clicking on the freq display and typing in the string you want.

Click here to see instructions on using the new WinTV Radio32 application.

Prodinfo: get information on your Hauppauge TV tuner

Prodinfo.exe is a program you can run which will extract information about the WinTV product you have installed such as model and serial number, MAC address, revision, and features which can be used to identify the exact model of your product. The driver for the device must be installed in order to run Prodinfo.exe

HCWClear: remove the Hauppauge driver and applications from your PC

HCWCLEAR.exe is a program you run to remove all driver and files that were installed with the installation of the Wintv program.

IR Blaster installation and configuration

IR Remote control version 28015

Remote control applet for use with WinTV 7. After you run this applet, an icon will appear in your Windows device tray showing that the Hauppauge remote control is active.

Is a free Personal Video Recorder PVR and Media Centre application for Microsoft Windows.

SnapStream Beyond TV 4 : Proving that a PC can rival TIVO .

Supports the latest Hauppauge TV tuners.

Record more than one show at the same time or watch one while recording another with multi-tuner support

Record an entire TV series Record one show, every episodes, or only new episodes of your favorite show

Enjoy the full screen interface Choose shows and setup recordings from the comfort of your couch

Easily find shows using the integrated Electronic Program Guide EPG

Record and watch HDTV shows with over-the-air HD support on the WinTV-HVR-1250

Skip commercials with SmartSkip

Find shows faster with the new browse by category feature, or search by title or keyword

Schedule recordings away from home via the Internet or a web-ready phone

Download FREE 21-day trial today

Processor Requirements minimum :

1.0 GHz Intel P4 or equivalent for cable TV

2.2 GHz Intel P4 or equivalent for ATSC digital TV

Microsoft Windows 10, 8, 7, Vista or Windows XP with Service Pack 2.

Available USB 2.0 port  does not work with a USB 1.1 port

Graphics with 64MB memory or greater

Specifications of the WinTV-HVR-1950/WinTV-HVR-1955

Antenna input for analog cable TV, over-the-air ATSC digital TV and clear QAM digital cable TV

Left and right audio via RCA jacks

MPEG-2 hardware encoder: Conexant -417 chip

Size: 10cm wide x 10.4 cm deep x 2.8cm high

Can I use the WinTV-HVR-1950 with Media Center.

Yes, the WinTV-HVR-1950 can be used in Windows 7, Windows XP or Vista Media Center.

Please note: you will only be able to configure WinTV-HVR-1950 as either a Digital tuner or an Analog tuner. You will not be able to switch between Digital and Analog channels.

What type of channels will I receive with the WinTV-HVR-1950.

NTSC Analog CableTV or over-the-air analog TV: You can use your cable TV from the wall to connect to the WinTV-HVR-1950 and receive all of your basic Cable TV channels. You can also use a roof top antenna to receive over-the-air TV.

Note: After June 2009, most areas in the United States no longer broadcast over-the-air analog signals.

ATSC over-the-air digital TV: Supports all ATSC formats, up to the high definition 1080i format.

Note: For ATSC digital TV, a rooftop/out door antenna is recommended for optimal results/signal strength.

ClearQAM cable TV Channels: Clear QAM digital cable TV channels are unencrypted digital cable TV channels. Clear QAM allows users to watch unencrypted digital TV channels from their cable TV provider without a set-top box.

Note: WinTV v7, WinTV v6, Microsoft Windows 7 or Windows TV Pack 2008 for Vista are required for clear QAM reception

Note: Check your local cable TV provider for clear QAM reception over your cable TV network

Can I get HD with the WinTV-HVR-1950 through my Cable or Satellite box.

No. The WinTV-HVR-1950 has an ATSC over-the-air digital TV receiver built-in and supports all ATSC formats, up to the high definition 1080i format. The WinTV-HVR-1950 will support ATSC broadcasts that are currently being transmitted over-the-air. It will not be able to decode HD broadcasts that come through your cable or satellite box. The WinTV-HVR-1950 also will support clear QAM cable TV channels through your direct cable TV line if available from your cable TV provider.

What type of recordings can I make with the WinTV-HVR-1950.

Using the WinTV 7 application the WinTV-HVR-1950 will record in a transport stream TS

For ATSC and Clear QAM digital TV recordings, the recording format and bit rate is exactly the same as the broadcast format i.e. ATSC 1080i is recorded at 1080i.

For NTSC analog cable TV recordings, our HardPVR is used to create Transport Stream files TS

Note: TS files can be converted to MPEG files using options in the WinTV 7 configuration menu.

Note: The WinTV 6 application recording are in MPEG format for both digital and analog.

Note: Not all recordings made with ATSC/QAM signals are DVD compliant.

Black video window or choppy video when watching a digital TV channel

If you are watching a digital TV channel and you see choppy video, no audio or a black screen, then it is possible your PC is not fast enough to decode and play the digital TV channel you are watching. Please verify that your system meets the minimum requirements for using the HVR-1950

Digital TV, especially ATSC high definition digital TV, is very CPU intensive. Many graphics cards have special built-in hardware to speed up decoding of high definition TV channels.

On graphics cards without special video decoding features, you can often improve the playback performance by using the Video Renderer settings located in the settings menu of WinTV 7. To open the setting menu click on the gear button located in the lower left of the WinTV 7 screen.

The default mode is EVR. The other modes are VMR9, VMR7 and Overlay. Each mode uses a different process to render video. Try each mode and use the one which gives you the best results. To use hardware acceleration put a check in the box use hardware acceleration when possible. This will allow your graphics system to use hardware acceleration for video decode. Note: graphics hardware acceleration does not work on all systems. After making a change in video rendering settings Wintv must be restarted to take effect.

If you are using WinTV 6 then the render options are part of a separate program called Primary.  Changes in the Primary applet must be made with the WinTV application closed.  Open the Primary program by going to Start – All Programs – Hauppauge WinTV – Primary.  After making changes close the Primary applet and open the WinTV application.

Connector overview for the WinTV-HVR-1950

What file size will the recorded videos be.

Digital Broadcasts ATSC or QAM

The file size of a digital signal capture depends on the bitrate of the digital signal.  The bitrate is set by the broadcaster and cannot be user configured.  Bitrates for digital signals can range anywhere from about 1.2 Mbits/sec up to 19.3 Mbits/sec.  Most of the time these bitrates are variable and not constant.  Capture sizes for ATSC QAM recordings are approximately 1.7 Gigabytes per hour up to 8.3 Gigabytes per hour.

The WinTV application has to convert analog signals to digital in order to record. There are four recording profiles. The following list shows recording file sizes for burning to 4.3Gb DVD:

WinTV v7 does not open or opens and then disappears.

This can be caused by a corrupt Channel database so you will need to uninstall and reinstall.  First you need to go to start, all programs, Hauppauge Wintv and in that folder run

uninstall Wintv7   or remove Wintv7 using control panel add/remove programs then you need to remove the backup channel database.

Windows Vista, 7 and 8 go to C: program data this folder is a hidden folder so if you do not see it you need to show hidden folders in your search

Options  once you can get to this folder you will see a folder label Hauppauge   delete this folder.

Windows XP go to C: documents and settings all users shared documents application data this folder is a hidden folder so if you do not see it you need to show hidden folders in your search Options  once you can get to this folder you will see a folder label Hauppauge   delete this folder.

Then download the latest version of Wintv7 located in the support section of the website and reinstall note: you must have your original CD to validate the download.

WinTV v7 error messages and what they mean

First time installation of WinTV v7 or during a reinstallation: WinTV board not found or No TV tuner available

Step 1: Check the status of your Hauppauge TV tuner drivers in Windows Device Manager

Click Windows Start, click on Control Panel and click on Device Manager

In Device Manager, click on Sound, video game Controllers

You should see your Hauppauge product

Step 2: If the Hauppauge device has a yellow exclamation mark

Click on the Hauppauge device to open it. If you see the following:

Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. Code 52

This appears to be a bug in Windows 64 bit OS since the Hauppauge Windows drivers are signed.

The following is the easiest fix to Error Code 52 on Windows 7 or Windows 8 64bit.

In Device Manager, right click the Hauppauge product under Sound Video and Game Controllers with the exclamation mark and select Uninstall. If you have a USB product you might see multiple listings, please right click the first one on the list.

For this example we will use the WinTV-HVR-950Q.

On the Confirm window please check the box for Delete the driver software for this device and click OK

Repeat the uninstall for the other two WinTV-HVR-950Q entries Note: you won t be asked to confirm device uninstall again

Once the drivers are removed, right click on Sound, Video, Game controllers and click Scan for Hardware Changes

Windows should now look online automatically for the 950Q drivers

Take a look after a few minutes if the drivers are installed automatically properly under Sound Video and Game Controllers.

If they still come back as unsigned try the procedure again

Errors when running WinTV 7: TVserver cannot Start or . NET framework errors

This can be caused by a corrupt WinTV v7 Channel Database. You will need to uninstall and reinstall the WinTV v7 application and the Channel database to fix this.

To uninstall WinTV v7, click Windows Start, click on All Programs, click on Hauppauge WinTV run Uninstall Wintv7. You can also or remove Wintv7 using control panel add/remove programs.

Then you need to remove the backup Channel database:

Windows Vista, 7 and 8: Go to C: program data this folder is a hidden folder so if you do not see it you need to show hidden folders in your search

Options once you can get to this folder you will see a folder label Hauppauge. Delete this folder.

Windows XP: Go to C: documents and settings all users shared documents application data this folder is a hidden folder so if you do not see it you need to show hidden folders in your search Options once you can get to this folder you will see a folder label Hauppauge delete this folder.

Settings.xml file is corrupt or missing

Solution: Uninstall WinTV v7 and then reinstall WinTV 7

Click Windows Start - Control Panel and then click Programs and Features

Find Hauppauge WinTV 7 and double click on this. This will start the uninstall process

When you are finished uninstalling WinTV v7, reinstall it from your WinTV v7 CD

Linux for the WinTV-HVR-1955, WinTV-HVR-1975 and WinTV-HVR-1950

Linux for the WinTV-HVR-1955 and the WinTV-HVR-1975

For the Linux driver, please send an e-mail message to: davidz hauppauge.com

Available through LinuxTV.org.

Included with the WinTV-HVR-1950 Hauppauge Computer Works ROM in your PC s CD-ROM drive. Hauppauge WinTV Installation CD-ROM Install the WinTV driver.

Note: As of August 2014, the WinTV-HVR-1955 is sometimes shipped instead of the HVR-1950. The HVR-1955 does not, at this time, have a open-source driver available.

Apr 08, 2011  Hauppauge WinTV HVR-1950 Model 1192. This is a versionactualizada from an article written earlier in this Blog, with very good result and executed without.

Hauppauge WinTV HVR-1950 (Model 75xxx, Hybrid ATSC/QAM) Driver Download

Latest applications and driver updates WinTV version 7 application and driver. Note: If you have run HCWCLEAR, you must reboot your PC and leave the WinTV-HVR-1950.

PC Pitstop / Driver Library / Hauppauge / Hauppauge WinTV HVR-1950 Model 75xxx, Hybrid ATSC/QAM

Welcome to the PC Pitstop Driver Library, the internet s most complete and comprehensive

source for driver information. PC Pitstop has developed numerous free scans that diagnose virtually all PC stability,

performance and security issues. Over the years, over 200 million scans have been run, and all that data has been compiled

to create our driver libraries.

Download the latest drivers for your Hauppauge WinTV HVR-1950 Model 75xxx, Hybrid ATSC/QAM to keep your Computer up-to-date.